Examtut

Central Florida Widgets recently installed a new router in their Apopka office. Complete the network installation by performing the initial router configurations and configuring RIPv2 routing using the router command line interface (CLI) on the Apopka router. To configure the router (Apopka) click on the console host icon that is connected to a router by a serial console cable (shown in the diagram as a dashed black line). Each of the windows can be minimized by clicking on the [-]. You can also reposition a window by dragging it by the title bar. The “Tab” key and most commands that use the “Control” or “Esc” keys are not supported and are not necessary to complete this simulation. The help command does not display all commands of the help system. Configure the router per the following requirements: Name of the router is Apopka Enable-secret password is ish555ana The password to access user EXEC mode using the console is New2Rtr The password to allow te...

  A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of 192.168.100.17 – 192.168.100.30. The following have already been configured on the router: - The basic router configuration - The appropriate interfaces have been configured for NAT inside and NAT outside. - The appropriate static route have also been configured (since the company will be a stub network, no routing protocol will be required) - All passwords have been temporarily set to “cisco”. The task is to complate the NAT configuration using all IP addresses assigned by the ISP to provide Internet access for the hosts in the Weaver LAN. Functionality can be tested by clicking on the host provided for testing. ...

An administrator is trying to ping and telnet from Switch to Router with the results shown below: For this question we only need to use the show running-config command to answer all the questions below: Router>enable Router#show running-config   Question 1 Which will fix the issue and allow ONLY ping to work while keeping telnet disabled? A. Correctly assign an IP address to interface fa0/1 B. Change the ip access-group command on fa0/0 from “in” to “out” C. Remove access-group 106 in from interface fa0/0 and add access-group 115 in. D. Remove access-group 102 out from interface s0/0/0 and add access-group 114 in E. Remove access-group 106 in from interface fa0/0 and add access-group 104 in Answer : E Explanation: The question was not about FTP so skip line #1 and line #2. The line #3 denies telnet traffic and line #4 permits icmp-echo traffic. L...

A network associate is configuring a router for the Weaver company to provide internet access. The ISP has provided the company six public IP addresses of 198.18.184.105 - 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of 192.168.100.17 – 192.168.100.30. The following have already been configured on the router: The basic router configuration The appropriate interfaces have been configured for NAT inside and NAT outside The appropriate static routes have also been configured (since the company will be a stub network, no routing protocol will be required.) All passwords have been temporarily set to “cisco” The task is to complete the NAT configuration using all IP addresses assigned by the ISP to provide internet access for the hosts in the weaver LAN. Functionality can be tested by clicking on the host provided for...

This task requires you to use the CLI of Sw-AC3 to answer five multiple-choice questions. This does not require any configuration. To answer the multiple-choice questions, click on the numbered boxes in the right panel. There are five multiple-choice questions with this task. Be sure to answer all five questions before leaving this item. Question 1: What interface did Sw-AC3 associate with source MAC address 0010.5a0c.ffba ? a.    Fa0/1 b.    Fa0/3 c.    Fa0/6 d.    Fa0/8 e.    Fa0/9 f.    Fa0/12 Explanation: We need find out a device that connected to Sw-AC3 with MAC-Address (0010.5a0c.ffba). Command: show mac-address-table If this command not works try show mac address-table Find the port name that has mac-address (0010.5a0c.ffba). Answer : D. Fa0/8 Question 2: What ports on...

After adding Interior router, no routing updates are being exchanged between Perimeter and the new location. All other inter connectivity and Internet access for the existing locations of the company are working properly. The Task is to identify the fault(s) and correct the router configurations to provide full connectivity between the routers. Access to the router CLI can be gained by clicking on the appropriate host. All passwords on all routers are cisco. IP Address are listed in the chart below Steps Remove invalid Autonomous System Number and add the correct Autonomous System Number Interior router. The Autonomous System Number is found in the topology: Add the network address of Fa0/0 interface of Perimeter router in EIGRP configuration. Because EIGRP neighbor relationship is not possible without the configuring connected interfaces. Answer Commands First we shou...

  A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed. The task is to create and apply a numbered access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted. Access to the router CLI can be gained by clicking on the appropriate host. All passwords have been temporarily set to “cisco”. The Core connection uses an IP address of 198.18.196.65 The computers in the Hosts LAN have been assigned addr...