Skip to main content

Based on the output from RouterA, what are two possible reasons for the failure?

Refer to the exhibit.

322


Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0.
Based on the output from RouterA, what are two possible reasons for the failure?(Choose two)

A. The cable that is connected to S0/0 on RouterA is faulty.
B. Interface S0/0 on RouterB is administratively down.
C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.

Answer : E, F

E: If no clock rate found on DCE end or no keepalive message received , then the Protocol Status changed to down.
F: Also if RouterA Serial0/0 and RouterB Serial S0/0 configured with two different protocols (Example: HDLC, PPP), then Protocol status will be changed to down.

Incorrect Choices

A, B: If cable is faulty or RouterB S0/0 is administratively down, then Status of RouterA S0/0 also in down.
C, D: If incorrect IP address and Subnet mask configured, the protocol status or physical status never on down state.

Labels:

Comments

  1. AdiSeptember 23, 2014 at 4:02 AM

    Hello Guys good news for you that CCNA discounted and Microsoft vouchers are now available. Now New CCNA (200-120) vouchers on special discount of 58% for World wide, with six months expiry date till you purchase.

    Details Required For CCNA Voucher For Discount Processing:

    1-First Name.
    Last Name. (as your name written in your National Identity card)
    2-Country.
    3-City.
    4-State.
    5-Pin Code (or Area Code)
    6-Residential Address (or where you can collect your Certificate or further correspondence
    can be received)
    7-Date of birth
    Add me on Skype through this information which is written below:
    Skype Name: rockon660
    you can also email me at this email address which is written below:
    madeelqaiser@gmail.com
    If you have any Questions feel free to contact me.

    Thanks,
    Best regards,
    Adeel

    ReplyDelete

Post a Comment

Popular posts from this blog

Access Control List (ACL) Simlet

An administrator is trying to ping and telnet from Switch to Router with the results shown below: For this question we only need to use the show running-config command to answer all the questions below: Router>enable Router#show running-config   Question 1 Which will fix the issue and allow ONLY ping to work while keeping telnet disabled? A. Correctly assign an IP address to interface fa0/1 B. Change the ip access-group command on fa0/0 from “in” to “out” C. Remove access-group 106 in from interface fa0/0 and add access-group 115 in. D. Remove access-group 102 out from interface s0/0/0 and add access-group 114 in E. Remove access-group 106 in from interface fa0/0 and add access-group 104 in Answer : E Explanation: The question was not about FTP so skip line #1 and line #2. The line #3 denies telnet traffic and line #4 permits icmp-echo traffic. L...
29 comments
Read more

Cisco Packet Tracer Multi User Connection

Multiuser communication allows multiple point-to-point (peer) connections between multiple instances of Packet Tracer. By allowing communication between Packet Tracer instances, a new door has been opened to a fun, interactive, social, collaborative, and competitive learning environment. Instructors will now be able to create a variety of activities for students to learn in groups that will facilitate greater social interaction between students. Students will benefit from this environment by working together to solve problems and share ideas. Both students and teachers should take full advantage that Multiuser will offer in their learning environment. Technical Information Communicates between instances using PTMP. PTMP is TCP based. By default, uses TCP port 38000, is customizable, and each new instances on the same PC will use the next available port. On by default. UPnP will attempt to establish port forwarding to facilitate home networks. All network co...
2 comments
Read more

New Questions in CCNA 200-120 (HSRP, VRRP, NetFlow, SNMP)

The below are mock questions that were about to appear in exam CCNA 200-120. Updated : 14 th October 2013 Download the Latest 200-120 dumps : Click Here This file requires Visual Cert Exam Suite: Click Here Download the latest 200-120 dumps in DOCX format : Chapter 1 , Chapter 2 , Chapter 3 , Chapter 4 , Chapter 5, Chapter 6, Chapter 7, Chapter 8 , Chapter 9, Chapter 10, Chapter 11, Chapter 12 CCNA EIGRP Simulation CCNA ACL2 Simulation Question 1 Which three are the components of SNMP? (Choose three) A. MIB B. SNMP Manager C. SysLog Server D. SNMP Agent E. Set Answer : A, B, D Question 2 What are the Popular destinations for syslog messages to be saved? A. Flash B. The logging buffer .RAM C. The console terminal D. Other terminals E. Syslog server Answer: B, C, E Question 3 Syslog was configured with a level 3 trap. Which 3 types of logs would...
121 comments
Read more