Skip to main content

What is the result of setting the no login command?

Refer to the exhibit. What is the result of setting the no login command?

image

 

A. Telnet access is denied.
B. Telnet access requires a new password at the first login.
C. Telnet access requires a new password.
D. There is a virtually limitless supply of IP addresses.

Answer : D

Explanation:

No Login command allows users to Telnet into a router with no password. Either way, something has to be configured for Telnet to work. Also, you cannot enter privileged mode (which is the IOS EXEC mode that allows you to view or change the configuration on a router) from Telnet unless an Enable password is set. These are very basic features of Cisco routers and allow only some security.


Screenshots

image

I just typed “ping 192.168.118.66”, Router R1 IP address:

image


image

Labels

Labels:

Comments

Post a Comment

Popular posts from this blog

Cisco Packet Tracer Multi User Connection

Multiuser communication allows multiple point-to-point (peer) connections between multiple instances of Packet Tracer. By allowing communication between Packet Tracer instances, a new door has been opened to a fun, interactive, social, collaborative, and competitive learning environment. Instructors will now be able to create a variety of activities for students to learn in groups that will facilitate greater social interaction between students. Students will benefit from this environment by working together to solve problems and share ideas. Both students and teachers should take full advantage that Multiuser will offer in their learning environment. Technical Information Communicates between instances using PTMP. PTMP is TCP based. By default, uses TCP port 38000, is customizable, and each new instances on the same PC will use the next available port. On by default. UPnP will attempt to establish port forwarding to facilitate home networks. All network co...
2 comments
Read more

A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts?

Refer to the exhibit. A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three.) A. host A IP address: 192.168.1.79 B. host A IP address: 192.168.1.64 C. host A default gateway: 192.168.1.78 D. host B IP address: 192.168.1.128 E. host B default gateway: 192.168.1.129 F. host B IP address: 192.168.1.190 Answer : A, C, F Explanation: Refer to the exhibit. Host A connected to Port 6 and Host B connected to Port 9. Also Port 6 and Port 9 associated with VLAN10 AND VLAN 20 respectively. In router Rtr1, the sub-interface fa0/0.10 and fa0/0.20 ‘s IP address will be used for Default Gateway for Host A and Host B. First take the IP address of fa0/0.10 – 192.168.1.78 /27 (255.255.255.224) Its IP range will be 192.168.1.65 – 192.168.1.94 Network Address – 192.168.1.64, Broadcast Address – 192.168.1.95 Second take the IP address of fa0/0....
3 comments
Read more

How to recover Cisco Router/Switch Password

The following is the tutorial about how recover a Cisco Passwords (Example: Console Password, Enable Password, Enable secret, VTY Password. But no need to removing case or CMOS Battery) Step 1: Restart / Power On the Router “R1” Step 2: Press Ctrl + Break, When the router is booting IOS. This key will interrupt the router boot process and prompt you ROM Monitor (ROMMON) Mode.   Step 3: Change the Configuration Register key to 0x2142 using confreg 0x2142 command. The key 0x2142 used to avoid coping configuration from NVRAM to RAM during next boot process. Then restart the router using reset command Step 4: After router restarted you will prompted for Initial Configuration. Type no to avoid Initial Configuration.   Step 5: Now the router with basic default configuration will be loaded. You can verify your passwords by show startup-config in Privilege EXEC mode.   ...
3 comments
Read more